面向客机总体设计的涡扇发动机分析模型

建立一种用于估算涡扇发动机特性的工程分析模型，该模型以涡喷发动机推力估算模型与涡扇发动机效率分析方法为基础，引入高涵道比涡扇发动机的循环分析方法进行修正。利用该模型可以获取涡扇发动机的推力和油耗特性，进而考察总体循环参数对发动机性能的影响。通过与文献验证数据对比，判定了分析模型的精度。该模型只需要输入少量参数就可以快速完成计算过程，适合于飞机总体设计阶段，可以评估涡扇发动机参数对飞机性能的影响。     

基于PAM-CRASH的蒙皮典型结构高速冲击仿真

以典型蒙皮结构为研究对象，分别对由2024－T3铝合金和碳纤维复合材料交替层压而成的FMLs以及2024－T3铝合金蒙皮进行高速冲击有限元仿真，并进行了损伤对比。其中，铝合金层和碳纤维层均采用最大应变准则。利用碰撞模拟分析软件PAM-CRASH以及采用SPH弹体对冲击模型进行仿真，结果显示在相同冲击能量下，加了支承结构的蒙皮在损伤抗性方面有了明显提升，并在此基础上分析不同的纤维铺层角度和铺层方式对FMLs蒙皮性能的影响。     

涡轮流量计前导流件有限元计算分析

对涡轮流量计关键部件之一前导流件运用NX THERMAL/FLOW进行有限元计算分析,得出流量分离导致的大涡旋尾迹区易出现在前导流件尾部区域、前导流件叶片形状对此处流体速度变化具有较大影响的结论,为涡轮流量计和前导流件的设计提供了理论依据。     

Forming and keeping fast fly-around under constant thrust

A new switching control algorithm under constant thrust is designed for the chaser fast flying around the target spacecraft along a specified fly-around trajectory. The switching control laws are obtained based on the acceleration sequences and the on time of thrusters which can be computed by the time series analysis method. The perturbations and fuel consumptions are addressed during the computation of the on time of thrusters. Furthermore, the relative position parameters of the target spacecraft are obtained by using the vision measurement and the target fly-around positions are calculated through the isochronous interpolation method. The change of the relative position and the relative velocity of the chaser during the constant thrust fast fly-around are presented through simulation example. It is proved that, with the switching control laws, the chaser will fast fly around the target spacecraft along the specified fly-around trajectory.     

发动机不可控高推力适航部分豁免方法研究

介绍了发动机不可控高推力(UHT)问题的产生背景,论述了申请§25.901(c)条款有关不可控高推力的部分豁免的思路和方法.结合FAA关于不可控高推力的指导材料,给出了有关不可控高推力的持续适航工作建议,对于飞机申请§25.901条款有关不可控高推力的部分豁免具有一定的指导意义     

Numerical Simulation of Rotor Flow Field Based on Overset Grids and Several Spatial and Temporal Discretization Schemes

A numerical method based on solutions of Euler/Navier-Stokes (N-S) equations is developed for calculating the flow field over a rotor in hover. Jameson central scheme, van Leer flux-vector splitting scheme, advection upwind splitting method (AUSM) scheme, upwind AUSM/van Leer scheme, AUSM+ scheme and AUSMDV scheme are implemented for spatial discretization, and van Albada limiter is also applied. For temporal discretization, both explicit Runge-Kutta method and implicit lower-upper symmetric Gauss-Seidel (LU-SGS) method are attempted. Simultaneously, overset grid technique is adopted. In detail, hole-map method is utilized to identify intergrid boundary points (IGBPs). Furthermore, aimed at identification issue of donor elements, inverse-map method is implemented. Eventually, blade surface pressure distributions derived from numerical simulation are validated compared with experimental data, showing that all the schemes mentioned above have the capability to predict the rotor flow field accurately. At the same time, vorticity contours are illustrated for analysis, and other characteristics are also analyzed.     

月球取样返回器分离阻力分析与地面分离试验验证

探月工程三期研制的月球取样返回器与轨道器间采用导向装配方式,装配后存在一定预应力,同时在轨两器分离时受空间环境作用而出现热变形,引起的分离阻力会对两器的正常分离产生影响。文章对返回器与轨道器的分离阻力进行分析和测量,并开展相关地面分离验证试验,结果表明,在轨环境引起的分离阻力约为366 N,地面装配应力引起的分离阻力约为160 N,两器分离速度约为0.24 m/s。研究结果可为轨返两器的分离设计提供参考。     

基于金属密封垫圈非线性变形仿真的预紧设计

为确保密封结构能有效阻止箱体内部介质的泄漏,要求密封面具备一定的密封比压,即通过施加合理的拧紧力矩来控制密封件的压缩量。目前主要采用试验方法验证一系列拧紧力矩下的密封效果,从而获取临界力矩值并确定可靠的拧紧力矩设计值。文章基于试验经验做出了合理的假设以建立简化的非线性有限元分析模型,对金属垫圈在压紧力下的塑性变形进行仿真,通过金属垫圈发生临界变形量的压紧力反推出拧紧力矩的临界值。该方法获取的临界力矩值与试验方法相近,可以有效地提高设计效率,降低试验成本。     

永磁同步直线电机建模及混沌搜索优化设计

建立了永磁同步直线电机的电磁场有限元物理模型,以此对气隙磁密波形畸变率进行了深入的分析。通过电机参数样本空间设计,利用正交试验设计方法进行非线性回归建模分析,给出了气隙磁密波形正弦度可行的电磁方案。基于混沌搜索理论和适应函数对永磁同步直线电机结构参数进行优化。仿真结果表明,在此结构参数基础上,电机磁极偏移后其三相反电势依然有较好的对称性,为永磁同步直线电机及其他的电磁工程设计提供了一种新的思路。     

Investigation of dynamics of discrete framed structures by a numerical wave-based method and an analytical homogenization approach

In this article, the analytical homogenization method of periodic discrete media (HPDM) and the numerical condensed wave finite element method (CWFEM) are employed to study the lon-gitudinal and transverse vibrations of framed structures. The valid frequency range of the HPDM is re-evaluated using the wave propagation feature identified by the CWFEM. The relative error of the wavenumber by the HPDM compared to that by the CWFEM is illustrated in functions of fre-quency and scale ratio. A parametric study on the thickness of the structure is carried out where the dispersion relation and the relative error are given for three different thicknesses. The dynamics of a finite structure such as natural frequency and forced response are also investigated using the HPDM and the CWFEM.